BÌNH TẠO BỌT CHUYÊN DỤNG CẦM TAY Venus Super Foamer HD TÍNH KIỀM

LÀ Máy tạo bọt có dung tích 2L. Phù hợp để pha các dung dịch có tính kiềm như nước rửa xe ô tô không chạm. Rất tiện lợi cho việc chăm sóc xe tại gia đình. Ngoài ra, bình còn được sử dụng để rửa, làm sạch và khử trùng các bề mặt như sàn, tường, mặt tiền trong sảnh sản xuất, nhà kho, cơ sở công nghiệp.

Nó được chứng minh hoàn toàn tốt trong việc tẩy dầu mỡ cho các dụng cụ và động cơ, cũng như loại bỏ dầu, mỡ và muội than trong nhà bếp công nghiệp.

ĐẶC TRƯNG:

SẢN PHẦM ĐI KÈM CÓ 3 ĐẦU TẠO ĐỘ BỌT ĐỂ DỄ DÀNG LỰA CHỌN KHI SỬ DỤNG: BỌT ƯỚT; BỌT TRUNG; VÀ BỌT TUYẾT KHÔ

CÓ VAN TAN TOÀN - ÁP SUẤT LUÔN ĐƯỢC KIỂM SOÁT

TAY CẦM TIỆN LỢI - LÀM VIỆC THOẢI MÁI

DẢI CHẤT LỎNG NHÌN THẤY - DỄ DÀNG THEO DÕI MỨC CHẤT LỎNG

VÒNG ĐẾ - ỔN ĐỊNH VÀ BẢO VỆ

MỐI NỐI EDPM

Thông số kỹ thuật:

capacity (l):Dung tích - 2L

pressure (bar):Áp lực: 2.2 bar

catalogue no.:Số hiệu catalogue: WTV.1186

Liquid flows out itself when pumping

Reason:

Absence or damage of "plug" gasket

Solution:

Unscrew the spraying tip from the pump body and check if the plug gasket is present in it; also check for damage or improper sitting. Replace in case of damage or absence.

Presence of liquid from the tank in the cylinder

Reason:

Damaged pump valve head.
Edges of the pump valve head soiled.

Solution:

Unscrew the pump from the head and check the condition of the pump valve head. Failure to adhere to the cylinder bottom, cracks, swelling or shrinkage of the gasket are symptoms of its damage. Replace it with a new one.
Dirt accumulated beneath the gasket edge may cause leakage. The problem should be eliminated after cleaning.

Problems with pumping, pump is letting liquid through

Reason:

Piston o-ring damaged.
No silicone oil on the o-ring surface

Solution:

Screw the pump off the sprayer head. Then, disassemble the pump by screwing out the pump body. After disassembly, inspect the o-ring for damage. If the o-ring is cracked or deformed, replace it.
After unscrewing the pump body, check if the o-ring is greased. In case of absence of silicone oil on the o-ring surface, grease it with silicone oil. After reassembling the pump, the device should operate correctly.

Inconsistent spray jet

Reason:

Damaged, clogged or improperly installed spraying tip.

Solution:

Unscrew the spraying nut and rinse it under running water. After reassembling, the nozzle should operate correctly. In case of permanent nozzle damage (miscalibration of the sprayer opening), replace the spraying tip with a new one.

Noticeable pressure decrease in the sprayer; safety valve fails to open or close, tank pressure falling

Reason:

Damaged safety valve.
Damaged sprayer head gasket.
Wrongly screwed sprayer pump or absence of gasket on the pump body.

Solution:

With the valve stem pulled aside, introduce several drops of silicone oil and open/close the valve several times. If the problem persists, replace the valve with a new one.
Check for presence of sealing element under the head (pump). Install a new one if absent; in case of damage (cutting, deformation), replace it with a new one.
Check that the o-ring on the pump body is not cut or damaged. In case of missing gasket under the pump body, install a new one or replace it if damaged.

Sprayer is spraying air instead of liquid

Reason:

The suction tube fell out of the fixing hole in the head body.

Solution:

Unscrew the sprayer head and insert the suction tube correctly by rotating until stop.

Liquid leaking from beneath the sprayer handle

Reason:

Damaged o-ring on the cut-off mandrel.
Faulty assembly of elements on the cut-off mandrel.

Solution:

With the spraying tip unscrewed and the "plug" gasket disassembled, introduce several drops of silicone oil into the hole on the head body and press the cut-off valve lever several times. If the problem persists, replace the cut-off mandrel with a new one.
Disassemble the mandrel assembly by removing it, and then place in the proper order (see manual).

seals:

EPDM

Professional technical sprayersVenus Super Foamer HD alka line

Foamer with the capacity 2L. It is used for washing, cleaning and disinfection of surfaces such as floors, walls, facades in production halls, warehouses, industrial facilities. It proves perfectly well in degreasing tools and motors, as also removing oils, grease and soot in industrial kitchens.

FEATURES:

3 foam endings in the set - for wet faom, medium foam and snow foam

safety valve – pressure always under control

convenient handle – work comfortably

visible fluid strip – easy to keep an eye on the fluid level

base ring – stabilization and protection

EPDM seals

Specifications

capacity (l):

pressure (bar):

2,2

catalogue no.:

WTV.1186

EAN:

5904447006746

seals:

EPDM

Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng).....

Thương hiệu: Kwazar

Bình Tạo Bọt Cầm Tay 2L Tính Kiềm Xuất Xứ Ba Lan - Hàng Chính Hãng